Plan your Sprinter conversion in 3D
Your Sprinter is already in the planner with its factory dimensions: nine variants from L1H1 to L4H3. Put in a bed, kitchen and bathroom and see straight away what fits and what clashes with the wheel arch or sliding door.
Trial: 1 design in a set van · no payment details · doesn’t renew
- 9 variants · L1H1 to L4H3
- 15 layout templates
- Right in your browser
Load space 3,272 × 1,787 × 1,974 mmDrag to rotateExample: Sprinter L2H2 · French bed (lengthways)- 9variants with factory dimensions
- 15ready-made layouts
- 90+item types
- 7days free trial
This is your Sprinter
With the sliding door open and the awning out, the view through the door, in the evening with the lights on, at night from above – and with the exterior dimensions. All pictures come straight from the planner.
By day
Sprinter L2H2 with “French bed (lengthways)”: sliding door open, awning out.
Through the sliding door
The first look inside – this is how your layout feels when you stand in front of the van.
In the evening
The same view with the lights on – cosy before you’ve laid a single cable.
Light throughout the van
All lights on – so you can see where it gets bright and where it stays dark.
Night mode
From above: beds and benches folded out, ready for the night.
5.93 m2.62 mExterior dimensions
Sprinter L2H2: 5.93 m long and 2.62 m high. Load space 3,272 × 1,787 × 1,974 mm.
By day
Sprinter L3H3 with “Single beds + half dinette + bathroom”: sliding door open, awning out.
Through the sliding door
The first look inside – this is how your layout feels when you stand in front of the van.
In the evening
The same view with the lights on – cosy before you’ve laid a single cable.
Light throughout the van
All lights on – so you can see where it gets bright and where it stays dark.
Night mode
From above: beds and benches folded out, ready for the night.
6.97 m2.83 mExterior dimensions
Sprinter L3H3: 6.97 m long and 2.83 m high. Load space 4,307 × 1,787 × 2,243 mm.
Power, water and weight for your Sprinter
The planner calculates your whole conversion, not just the furniture – and at the end you know exactly what to buy. Power, water, insulation and axle loads are included in Monthly and the Project Pass, the shopping lists (build kits) in the Project Pass.
Plan your power
Enter your appliances – cool box, lights, heater, laptop. The planner works out your daily consumption, how long your leisure battery lasts and how quickly solar, the alternator and shore power recharge it. Plus cable size and fuse for every circuit.
Plan your water
Tank, pump and boiler: the planner shows how many litres you need per day, how long your tank lasts and how much hot water the boiler delivers – including pipe lengths to every tap.
Weight and axle loads
Every item brings its weight to its spot. The planner spreads everything over the front and rear axle, also with full tanks and passengers, and warns you before your Sprinter gets too heavy.
Shopping lists for your Sprinter
Your design becomes a ready-made shopping list: the power kit (battery, chargers, fuses, cables in the right size and length), the water kit (tank, pump, boiler, pipes, taps), the cutting kit (wood and boards with cutting plan and cut list) and the insulation kit (insulation per surface in whole rolls and boards, adhesive and tape) – made for your Sprinter. Tick off, share or take along as PDF and CSV.
Insulation
Material and thickness for roof, walls, doors, floor and wheel arches – or a ready-made package: Summer, Four seasons or Winter sports. The planner calculates the heat loss, checks whether your heater is up to it and where condensation can form, and shows the manufacturer’s installation guideline for your Sprinter.
GasSoon
Plan the gas bottle, hob and gas heater safely, with everything you need for it. Coming soon – also with a shopping list.
Ready-made layouts for your Sprinter
Pick a template and the planner fits all the furniture into your Sprinter. You can then rearrange any template freely.
Sprinter L2H2Transverse bed + kitchen + seating
Fixed transverse bed at the rear with a garage underneath, kitchen along the left wall, swivel seat and table.
Sprinter L2H2French bed (lengthways)
Lengthways double bed at the rear on the left, walkway on the right, kitchen up front.
Sprinter L2H2Twin single beds
Two single beds along the sides with a walkway between them, garage underneath.
Sprinter L2H2Rock and roll bed
Bench seat at the rear that folds flat into a bed at night (rock and roll bed), kitchen along the left wall. For compact and low-roof vans.
Sprinter L2H2Transverse bed + L-bench
Fixed transverse bed plus an L-shaped bench that becomes a second bed, using the table as a support.
Sprinter L2H2Workspace: seating + transverse bed + toilet
For working on the road: seating area with table and laptop, kitchen, toilet cubicle and a fixed transverse bed. In a longer van a bench faces the swivel seats.
Sprinter L2H2Garage bed with slatted base + workspace
Garage at the rear with a slatted base that slides forward at night and then rests on a height-adjustable table, and on the worktop where possible. By day that table is your workspace, with an L-shaped bench or benches around it.
Sprinter L2H2Lounge on a platform
Platform with drawers at the rear over the wheel arches, with an L-bench on top that becomes a transverse bed at night. Kitchen with tiled splashback and an open shelf unit, and a step up to the platform.
Sprinter L2H2Felt lounge
U-shaped bench at the rear with felt-covered seat boxes and sage green cushions, which becomes one large bed at night using the table. Kitchen on the left, wooden ceiling, shiplap wall and a loose seat box.
Sprinter L2H2Side benches with pedestal table
Two ochre velvet benches facing each other with a pedestal table in between. By day a walkway to the rear doors, at night one bed across the full width. Open shelves on the rear doors.
Sprinter L3H2Transverse bed + bathroom
Transverse bed at the rear, wet room with toilet in front of it, kitchen and seating up front.
Sprinter L3H2Transverse bed + half dinette + bathroom
The classic campervan layout: half dinette behind the driver, bathroom on the left, kitchen on the right behind the sliding door and a transverse bed at the rear.
Sprinter L3H2Single beds + half dinette + bathroom
Two single beds at the rear with a garage underneath, half dinette up front, bathroom on the left and kitchen on the right. For long vans.
Sprinter L3H2Bunk beds + half dinette + bathroom
Two transverse beds stacked at the rear, ideal for children, with a half dinette, bathroom and a kitchen by the sliding door.
Sprinter L3H2Pull-out transverse bed + bathroom
A narrow transverse bed that pulls out into a double at night, so you have more living space by day. Bathroom up front, kitchen on the left.
What matters in a Sprinter
Four questions almost everyone asks when converting a Sprinter, answered by the planner before you buy materials.
Transverse or lengthwise bed?
The load space is 1,787 mm wide. The planner starts with a 30 mm wall build-up per side: 18 mm battens plus 12 mm cladding boards. Behind the ends of the bed it leaves the cladding out. That leaves about 1.75 m between the battens: tight, but enough for a transverse bed. Too short for you, or building a thicker wall? From the L2 up, choose a French bed or twin single beds.
How much headroom do you need?
H2 gives 1,974 mm of load space height, H3 as much as 2,243 mm. What is left after the floor and ceiling build-up decides whether you can stand upright. In the planner you switch variants and compare directly.
Weight and axle loads
If you want to drive on a category B licence, the gross vehicle weight must not exceed 3.5 t. The planner starts with the kerb weight of your variant, spreads every item over the front and rear axle and warns you before an axle is overloaded. The axle load calculation is included in Monthly and the Project Pass.
Sliding door and wheel arches
The sliding door is 1,300 mm wide and there are 1,350 mm between the wheel arches. If the kitchen blocks the door opening or a cabinet hits a wheel arch, it turns red straight away, with the measurement in millimetres.
Three steps to your layout
Everything runs in your browser – nothing to install. You create an account and try it free for 7 days.
Choose your Sprinter
Choose your variant (with Monthly or the Project Pass) and enter your wall build-up. The planner then works with the net interior dimensions – not the bare metal.
Build your layout
Start from a template or drag items in: beds, kitchen, bathroom, water tank, battery, heater and more – over 90 item types, every dimension to the millimetre.
Check and save
Collisions turn red and your design is saved automatically. Weight, axle loads and exporting the parts list come with Monthly or the Project Pass.
All Sprinter variants with factory dimensions
Load space, wheelbase and overall length come from the manufacturer’s specifications. Click “Open” and the variant starts straight away in the planner.
Model year from 2018 · rear-wheel drive · load space width 1,787 mm · width between the wheel arches 1,350 mm · sliding door width 1,300 mm
| Variant | Load length | Load height | Wheelbase | Overall length | |
|---|---|---|---|---|---|
| L1H1 | 2,607 mm | 1,719 mm | 3,259 mm | 5.27 m | Open → |
| L1H2 | 2,607 mm | 1,974 mm | 3,259 mm | 5.27 m | Open → |
| L2H1 | 3,272 mm | 1,719 mm | 3,665 mm | 5.93 m | Open → |
| L2H2 | 3,272 mm | 1,974 mm | 3,665 mm | 5.93 m | Open → |
| L2H3 | 3,272 mm | 2,243 mm | 3,665 mm | 5.93 m | Open → |
| L3H2 | 4,307 mm | 1,974 mm | 4,325 mm | 6.97 m | Open → |
| L3H3 | 4,307 mm | 2,243 mm | 4,325 mm | 6.97 m | Open → |
| L4H2 | 4,707 mm | 1,974 mm | 4,325 mm | 7.37 m | Open → |
| L4H3 | 4,707 mm | 2,243 mm | 4,325 mm | 7.37 m | Open → |
Frequently asked questions
Can I plan an older Sprinter too?
The planner has the Sprinter from model year 2018 with rear-wheel drive. For an older model, choose “Custom dimensions” and enter the length, width and height of your load space. The planner then starts from the closest variant and uses your dimensions.
What does the planner cost?
You try it free for 7 days, without payment details: one design in a set van, with all parts and templates, collision checks and day/night. After that the trial ends by itself: no subscription keeps running and you can still view your design. More designs, a different van or variant, the power and axle load calculations and the export come with Monthly (€7.99 per month, cancel any month) or the Project Pass (€39.99 one-off, 12 months of access). Prices include VAT.
How accurate are the dimensions?
Load space, wheelbase and exterior dimensions come from the manufacturer’s specifications, as do the door dimensions where known. The position and size of the wheel arches and the shape of the side walls, which slope inwards towards the top, are estimates that you can adjust in the planner. Always measure your own van before cutting anything.
Does it work on a phone?
Yes. You drag items with one finger, rotate the view with one finger on an empty spot and zoom with two fingers. For fine-tuning dimensions a laptop is more comfortable, though.
Does the planner replace a vehicle inspection?
No. The planner helps you plan and check, but it does not replace professional advice on the construction, an inspection or approval by your vehicle authority (such as the RDW in the Netherlands or TÜV and DEKRA in Germany), or measuring your own van.
Your Sprinter is ready and waiting in 3D
Trial: 1 design in a set van · no payment details · doesn’t renew · right in your browser